Description
xNOTICE:
Upgrade in new version.
1. Upgrade in new F4 Flight Controller with 9V 5V BEC Output
2. Upgrade in new 60A BL_S 4in1 ESC
3. Don't have Side Protection Plate anymore
Dear customers,
Attention please.
The flexible glue anti-vibration motor pad may cause the motor to slip, please check and tighten the screws before flying.
Best regards,
Banggood
Description:
| New Version | Old Version | |
| Flight Controller |
Model:F4DUALBEC8MOTOR0616 Main Chip: STM32F405 Gyro: MPU6000 Barometer: BMP280 Blaxkbox: 16M Motor Output: 8 Size: 37x37mm Mounting Hole: 30.5x30.5mm BEC Output: 9V, MAX. 2A ; 5V Max.3A |
Omnibus F4 V3 flight controller Size: 36x36mm
Mount holes: 30.5x30.5mm
STM32 F405 MCU, Runs Betaflight 3.0.1 firmware, could run faster loop time.
Using F4 MCU controls OSD over SPI bus in DMA mode.
OSD Configation has been included in Betaflight GUI.
SBUS/PPM input (Pinheaders)
6PWM output (1-4Pinheaders and Sh1.0 Plug, 5-6 as Pinheaders)
With barometer
SPI Sensor MPU6000
Included 128Mbit Flash, please always use BEC for the FC. Supported by BETAFLIGHT and dRonin
|
| ESC |
Con. current: 60A Mounting Hole: 30.5x30.5mm Notice: iF use in 6S, Must solder the capacitor, which is included in package. |
Eachine 30A BLHELI_S 4 in 1 ESC Con. current: 30A |
| Item | Specification | |
| Eachine Wizard X220S |
Wheelbase: 220mm Frame arm: 4mm carbon fiber Weigh: 356g (without battery and camera mount) Take off weigh: 561g
3K carbon fiber frame kit, 4mm thickness and 15mm width frame arms, the width is 10mm less than Eachine Wizard X220.
Frame kit with camera angle scale and 30° camera mount for Runcam 3 for Gopro session.
Anti-vibration sponges to protect the racer frome crashing.
|
|
| Eachine MN2206 2300KV motor |
KV: 2300 Max thrust: 1100G Length: 35MM NO.OF cell: 3-5S Diameter: 28MM Framework: 12N14P Shaft: 5mm Propeller: 5 inch Weight: 28g |
|
| Eachine 1179 800TVL CCD camera |
Color: purple Sensor: CCD
Resolution(horizontal center): 800TVL
Shell size: 25mm*25mm
Weight: 11g
Resolution: PAL: 1980H×1080 (2MP)
Format: PAL
Video output: 1.0Vp-p/75Ω
Automatic gain control: 0.25/0.50/0.75/1.00 adjustable, up to 55dB.
AWB: ON/OFF
Exposure mode: electron exposure
Electronic shutter: 1/50(1/60) - 1/100000 S
Gamma correction: 0.45/1.0
Synchronization method: internal synchronization
Lens: standard 2.8mm lens
Working voltage: DC12V (Wide Voltage, measured that can be work in 5-13V)
Workig current: 70mA (low power consumption)
Workig temperature: -20℃--60℃
Humidity: 0%~98% Strong backlighting effect |
|
|
5.8G 40CH 25MW 200mw 600MW switchable transmitter
|
Video Format : NTSC/PAL Channel: 40CH Operating Temperature : -10~85℃ Connector: RP-SMA Female
Antenna connector: RP-SMA Male
|
|
| Eachine 5051 3-blade propeller |
Color: Send Randomly Quantity: 10 Pairs Mounting Hole: 5mm |
|
This is the ARF version that comes without battery, charger, receiver and remote control.
Package included:
1 x Eachine Wizard X220S frame kit
2 x 2206 2300KV motor CW
2 x 2206 2300KV motor CCW
1 x Eachine 30A BLHELI_S 4 in 1 ESC
1 x Omnibus F4 V3 flight controller
1 x 1179 800TVL camera
1 x 5.8G 40CH 25MW 200mw 600MW switchable VTX
10 x Eachine 5051 3-blade propeller purple CW
10 x Eachine 5051 3-blade propeller purple CCW
1 x 30° Camera Mount(For Runcam3/ for Gopro session)
1 x Pagoda antenna
2 x Battery strap
2 x Wrench
(Package doesn't include Runcam 3, the Runcam 3 on the pictures for reference only.)
(Package doesn't include Runcam 3, the Runcam 3 on the pictures for reference only.)
- Choosing a selection results in a full page refresh.